Brazoria County · Storage & Organization

Custom Laundry Room Cabinets in Angleton, TX

From folding counters to hamper pull-outs, Ace Kustoms builds custom laundry room cabinets for Angleton and the rest of Brazoria County.

Free Estimate in Angleton Call (281) 660-3903

Custom Laundry Room Cabinets for Angleton homes

Angleton is the Brazoria County seat, located on SH 288 roughly halfway between Pearland and Lake Jackson. It has the county courthouse, an older downtown and residential neighborhoods that spread out into farm and ranch land. The Brazosport cities and the coast are a short drive south, and Houston is about 45 minutes north on 288.

Angleton has many homes from the 1950s through the 1980s, often single-story ranch houses with compact kitchens, plus newer subdivisions and rural properties. Kitchen remodels that rework closed layouts, vanity updates and garage storage are common. Acreage homes also ask for mudrooms and shop cabinets.

Smaller laundry spaces in Angleton homes and townhomes call for careful planning. A stacked washer and dryer, a tall cabinet and a slim pull-out for detergent can turn a closet into a functional laundry. Shallow upper cabinets and wall-mounted drying racks keep the floor clear while still providing storage. A small counter or fold-down shelf can still fit beside the machines, and lighting under the uppers makes a dark closet much easier to work in.

Every project starts with an in-home measurement in Angleton. We build in our Houston shop and the same crew handles installation, so the person you talk to at the estimate is accountable for the result. Learn more about our full custom laundry room cabinets service.

What you get with Ace Kustoms

Sorting without the clutter

Pull-out or tilt-out hampers for darks, lights and towels keep dirty laundry sorted and hidden. Bins lift out for carrying to the machines, so piles stop gathering on the floor.

Ironing and sewing storage

A pull-out ironing board in a drawer, a fold-down board in a wall cabinet or a tall cabinet for a full-size board. Irons, starch and a small sewing kit get their own shelf.

Folding counter over front-loaders

A countertop installed above side-by-side front-load machines gives you a full-width folding surface where there was dead space. We leave clearance for vibration and set the height so the counter is easy to use.

Supplies off the floor

Upper cabinets and pull-outs hold detergent, stain removers, dryer sheets and cleaning supplies. Child locks or high storage keep pods and chemicals away from small children and pets. Pull-outs put everything in view.

Popular options in Angleton

Stacked machines with tall cabinet

A stacked washer and dryer beside a tall cabinet for brooms, the vacuum and an ironing board. Frees up wall space for a sink or folding counter in narrow rooms.

Laundry sink base

A deep single-bowl utility sink or an undermount sink in a counter, set in a sealed base cabinet with a waterproof floor liner. Handy for hand-washing, soaking stains and rinsing muddy items.

Hamper and sorting pull-outs

Double or triple pull-out hampers with removable bins, or tilt-out hamper doors. Sized for standard laundry bins and placed next to the washer for easy loading. Bins lift out so you can carry them to the machine.

Open shelving and cubbies

Open shelves for baskets and folded towels, or cubbies for each family member's clean laundry. Painted or stained hardwood shelves add warmth to a mostly white utility room. Baskets can be labeled.

White shaker kitchen with glass-front upper cabinets

Installer mounting a drawer slide with a drill

How a Angleton project runs

Measure machines and utilities. We measure the room and your washer and dryer, then locate water supply, drain, dryer vent, gas line if any and outlets. These set where cabinets can and cannot go.
Plan the work flow. You review a layout that follows the laundry process: sort, wash, dry, fold, hang and put away. We place hampers, counters and rods in the order you use them.
Select finishes and counters. You choose cabinet color, hardware and countertop from real samples. We recommend moisture-resistant options for areas near the sink and machines. We also look at how each sample handles water spots and detergent drips.
Build and seal in our shop. We build plywood cabinets in our Houston shop, sealing every surface and lining the sink base, then finish them before delivery so they are ready for daily use.
Install and test clearances. The crew installs cabinets and counter supports, checks clearance around machines, vents and valves, and confirms the washer and dryer can be pulled out for service.

Local conditions we plan for

Houston laundry rooms combine high outdoor humidity with washer moisture and dryer heat, which is hard on cabinets. Sealed plywood construction and moisture-resistant finishes are important. Dryer vents should run the shortest path to the outside, and we never block or crush them behind cabinets. On slab foundations, moving machines or adding a sink means trenching concrete, so we work with existing plumbing whenever possible. A washer pan with a drain, or at least a leak sensor, is a good idea for upstairs laundry rooms common in newer two-story homes.

Much of Brazoria County is low, flat and close to the Gulf, so humidity and salt air are constant factors. We use plywood boxes, sealed edges and durable finishes, and we pay attention to hardware selection in homes near the coast where corrosion is a concern. For homes in flood-prone areas, raised toe kicks and moisture-resistant materials in the lowest components can make recovery easier after high water.

For general planning, laundry room cabinets with uppers and a folding counter in Greater Houston often run around $4,000 to $9,000, while larger rooms with a sink, tall storage and specialty pull-outs can range from $10,000 to $20,000 or more. These figures vary with size, materials and site conditions, so ask for a written estimate after we measure.

Custom Laundry Room Cabinets in Angleton: FAQs

What about an upstairs laundry room?

Upstairs laundry rooms, common in newer Houston homes, benefit from a washer drain pan, leak sensors and sealed cabinetry. We plan cabinets so the pan and shut-off valves remain accessible and do not get covered by panels or counters. Access panels can be built in.

Can I keep my existing machines?

Yes. We measure your current washer and dryer and design openings with some extra space for future replacements. If you plan to buy new machines soon, choosing them first lets us build the cabinets to their exact dimensions. Many new machines are larger.

Can you put a countertop over my washer and dryer?

Yes, with front-load machines. We install a counter supported by cleats or side panels, not resting on the machines, with clearance for vibration and to slide the machines out for service. The height is set so you can open the doors and still fold comfortably.

Does Ace Kustoms work in Angleton?

Yes. Angleton is part of our regular service area in Brazoria County, along with nearby Richwood, Danbury, Lake Jackson, Clute. We schedule in-home measurements throughout the week and the estimate is free.

How do I get an estimate in Angleton?

Call (281) 660-3903, text us, or send the form on this page with a few photos and rough measurements. We will set up an in-home visit, measure the space and follow up with a written, itemized estimate.

More services in Angleton

Explore

Planning guides

Storage & Built-Ins · 7 min read