Brazoria County · Kitchens & Baths

Custom Bathroom Vanities in Angleton, TX

Looking for a vanity that actually fits your Angleton bathroom wall? Ace Kustoms builds them to the inch for homeowners across Brazoria County.

Free Estimate in Angleton Call (281) 660-3903

Custom Bathroom Vanities for Angleton homes

Angleton is the Brazoria County seat, located on SH 288 roughly halfway between Pearland and Lake Jackson. It has the county courthouse, an older downtown and residential neighborhoods that spread out into farm and ranch land. The Brazosport cities and the coast are a short drive south, and Houston is about 45 minutes north on 288.

Angleton has many homes from the 1950s through the 1980s, often single-story ranch houses with compact kitchens, plus newer subdivisions and rural properties. Kitchen remodels that rework closed layouts, vanity updates and garage storage are common. Acreage homes also ask for mudrooms and shop cabinets.

Families in Angleton with kids sharing a bathroom often ask for two sinks, a separate drawer stack for each child and a step-friendly toe-kick. Durable painted maple or stained oak holds up to daily use, and soft-close slides keep slamming to a minimum during the morning rush. We can also add a hamper pull-out or towel storage so the counter stays clear and each kid has an assigned spot for their things.

Every project starts with an in-home measurement in Angleton. We build in our Houston shop and the same crew handles installation, so the person you talk to at the estimate is accountable for the result. Learn more about our full custom bathroom vanities service.

What you get with Ace Kustoms

Exact width and height

We size the vanity to your wall, leaving code-friendly clearance to the toilet centerline and room for door swing. Counter height is set to suit you, typically 34 to 36 inches for adults, with a toe-kick tall enough to clear baseboard.

Plumbing-aware interiors

Drawers are notched or U-shaped around the trap so you keep usable storage under the sink. We locate drain and supply stub-outs before building, so we do not end up with a drawer that cannot close over a P-trap.

Real wood finish

Doors and drawer fronts are solid hardwood, and painted vanities use paint-grade maple with a catalyzed finish that stands up to cleaners, hair products and toothpaste far better than thermofoil or wrapped panels.

Matched storage pieces

We can build linen towers, recessed medicine cabinet surrounds, or a makeup area at seated height in the same wood and finish, so the bathroom looks planned rather than pieced together from different stores.

Popular options in Angleton

Wood species and finish

White oak and walnut look warm against tile and resist moisture well under a sealed finish. Painted maple in white, gray or navy is popular. We show finished samples next to your tile choice so the colors work together.

Hardware and drawer layout

Choices include full-extension soft-close slides, hair-tool drawers with a vented outlet, divided drawers for makeup, and tip-out trays at the sink front. Pulls can be brass, black, nickel or edge-grip for a seamless look.

Floating vanities

Wall-hung vanities mount to blocking inside the wall and leave the floor open below, which makes small baths feel larger and simplifies mopping. Typical depth is 18 to 21 inches, and we often add under-cabinet LED lighting for a night light.

Furniture-style vanities

Legs, a recessed base and furniture-style moldings give a vanity the look of a freestanding chest. These suit traditional homes and powder rooms, and we build them in walnut, cherry or painted maple with turned or tapered legs.

Modern bathroom with an oak floating vanity, round mirror and freestanding tub

Gray shaker bathroom vanity with a white top

How a Angleton project runs

Measure and plumbing check. We measure the wall, check plumbing locations, look at outlets and mirror placement, and note floor and wall conditions. If the drain needs to move for a wider vanity, we flag that before design starts.
Design and material samples. You choose size, layout, wood species, finish, sink type and hardware with real samples. We confirm the counter material and sink model so the cabinet is sized for its cutout and weight.
Shop build and finishing. We build the box, doors and drawers in our shop and spray the finish in a controlled booth, sealing all surfaces including the back and underside for moisture protection.
Installation. Our crew removes the old vanity if needed, adds wall blocking for floating units, levels and anchors the cabinet, and prepares it for the top. We coordinate countertop install and plumbing reconnection.
Walkthrough and adjustment. After the top and faucet go in, we adjust doors and drawers, check for leaks under the sink, and walk you through finish care and any final punch list items.

Local conditions we plan for

Bathrooms in Houston see moisture from both directions: steam from inside and humid air from outside, especially in homes where the AC cycles less during mild months. That is why we build vanities from plywood, seal every surface and leave a small gap at the floor so mopping water does not wick into the base. Many older slab homes have drains coming up through the floor rather than the wall, which limits drawer layouts, so we plan around them. In coastal areas, we choose hinges and slides with better corrosion resistance. We also recommend an exhaust fan that vents outdoors, since no finish will survive a bathroom that stays damp for hours.

Much of Brazoria County is low, flat and close to the Gulf, so humidity and salt air are constant factors. We use plywood boxes, sealed edges and durable finishes, and we pay attention to hardware selection in homes near the coast where corrosion is a concern. For homes in flood-prone areas, raised toe kicks and moisture-resistant materials in the lowest components can make recovery easier after high water.

As a general planning range, a custom single-sink vanity in Greater Houston often starts around $1,800 to $3,500 installed for the cabinet, while a 72-inch double vanity with drawers may run roughly $4,000 to $8,500 before countertop and plumbing. Final cost depends on size, materials and site conditions, so please get a written estimate after an in-home measure.

Custom Bathroom Vanities in Angleton: FAQs

Can a floating vanity hold a stone top?

Yes, when it is mounted correctly. We add solid wood blocking between studs behind the vanity and fasten the cabinet through its back rail into that blocking. A 60-inch quartz top can weigh well over 100 pounds, so the blocking matters more than the cabinet itself. Retrofit may require opening drywall.

Will a wood vanity survive bathroom humidity?

A properly built and sealed one will. We use plywood boxes, solid wood doors with floating panels, and a catalyzed finish on all sides. The bigger risk is standing water, so wipe spills and fix drips promptly. A working exhaust fan also helps the vanity and the rest of the room.

Can you build a vanity around existing plumbing?

Usually, yes. We measure drain and supply positions and design drawers with cutouts or U-shapes around the trap. If you want a wider vanity or a second sink, a plumber may need to move or add a drain, which we identify during the estimate.

Does Ace Kustoms work in Angleton?

Yes. Angleton is part of our regular service area in Brazoria County, along with nearby Richwood, Danbury, Lake Jackson, Clute. We schedule in-home measurements throughout the week and the estimate is free.

How do I get an estimate in Angleton?

Call (281) 660-3903, text us, or send the form on this page with a few photos and rough measurements. We will set up an in-home visit, measure the space and follow up with a written, itemized estimate.

More services in Angleton

Explore

Planning guides

Bathrooms & Vanities · 7 min read