Custom Laundry Room Cabinets in Richmond, TX

Custom Laundry Room Cabinets for Richmond homes

Richmond is the Fort Bend County seat, set on the Brazos River southwest of Sugar Land. Its historic downtown holds county government buildings and older homes, while newer subdivisions and master-planned communities spread out around it. It borders Rosenberg to the west, and US 59 and US 90A connect it to Houston.

Richmond has historic homes near downtown, mid-century houses and many newer subdivisions. Older homes can have pier-and-beam floors and plaster walls, calling for careful leveling and trim matching, while newer homes want builder-grade upgrades, scullery pantries and mudroom drop zones. Rural properties nearby often need garage and shop storage.

Newer homes in Richmond usually have dedicated laundry rooms, sometimes upstairs, but builders often install only a single wire shelf. Homeowners ask us to add upper cabinets, a folding counter and a sink. Upstairs laundry rooms benefit from sealed cabinets and leak protection, and we plan around drain pans and shut-off valves so they remain reachable after installation. Done early, it avoids clutter.

Every project starts with an in-home measurement in Richmond. We build in our Houston shop and the same crew handles installation, so the person you talk to at the estimate is accountable for the result. Learn more about our full custom laundry room cabinets service.

What you get with Ace Kustoms

Folding counter over front-loaders

A countertop installed above side-by-side front-load machines gives you a full-width folding surface where there was dead space. We leave clearance for vibration and set the height so the counter is easy to use.

Supplies off the floor

Upper cabinets and pull-outs hold detergent, stain removers, dryer sheets and cleaning supplies. Child locks or high storage keep pods and chemicals away from small children and pets. Pull-outs put everything in view.

Moisture-resistant construction

Sealed plywood boxes, finished interiors and a waterproof liner or sealed floor in the sink base protect against drips and leaks. Particleboard cabinets swell quickly when exposed to water in a laundry room.

Hanging and drying built in

A rod under the upper cabinets for hanging shirts straight from the dryer, plus a fold-down or pull-out drying rack for delicates. Clothes stay wrinkle-free and air-dried items have a dedicated place.

Popular options in Richmond

Hamper and sorting pull-outs

Double or triple pull-out hampers with removable bins, or tilt-out hamper doors. Sized for standard laundry bins and placed next to the washer for easy loading. Bins lift out so you can carry them to the machine.

Open shelving and cubbies

Open shelves for baskets and folded towels, or cubbies for each family member's clean laundry. Painted or stained hardwood shelves add warmth to a mostly white utility room. Baskets can be labeled.

Finishes and countertops

Painted finishes in white, gray, green or blue with laminate, quartz or solid surface counters. Butcher block looks warm but needs sealing and care near the sink and machines. We bring samples of each.

Side-by-side machines with counter

Front-load washer and dryer under a continuous countertop with upper cabinets above and a narrow pull-out between machines for detergent. A common layout that makes the most of a single wall.

Pantry shelving stocked with glass storage jars

White shaker kitchen with glass-front upper cabinets

How a Richmond project runs

Measure machines and utilities. We measure the room and your washer and dryer, then locate water supply, drain, dryer vent, gas line if any and outlets. These set where cabinets can and cannot go.
Plan the work flow. You review a layout that follows the laundry process: sort, wash, dry, fold, hang and put away. We place hampers, counters and rods in the order you use them.
Select finishes and counters. You choose cabinet color, hardware and countertop from real samples. We recommend moisture-resistant options for areas near the sink and machines. We also look at how each sample handles water spots and detergent drips.
Build and seal in our shop. We build plywood cabinets in our Houston shop, sealing every surface and lining the sink base, then finish them before delivery so they are ready for daily use.
Install and test clearances. The crew installs cabinets and counter supports, checks clearance around machines, vents and valves, and confirms the washer and dryer can be pulled out for service.

Local conditions we plan for

Houston laundry rooms combine high outdoor humidity with washer moisture and dryer heat, which is hard on cabinets. Sealed plywood construction and moisture-resistant finishes are important. Dryer vents should run the shortest path to the outside, and we never block or crush them behind cabinets. On slab foundations, moving machines or adding a sink means trenching concrete, so we work with existing plumbing whenever possible. A washer pan with a drain, or at least a leak sensor, is a good idea for upstairs laundry rooms common in newer two-story homes.

Fort Bend sits on flat, low ground along the Brazos River and its creeks, and humidity stays high most of the year. We use plywood boxes and stable door construction to handle seasonal swelling. For homes in areas that have seen high water, we can discuss raised toe kicks, moisture-resistant bases in laundry rooms and garages, and finishes that tolerate wipe-downs. Good ventilation in bathrooms protects vanity finishes over time.

For general planning, laundry room cabinets with uppers and a folding counter in Greater Houston often run around $4,000 to $9,000, while larger rooms with a sink, tall storage and specialty pull-outs can range from $10,000 to $20,000 or more. These figures vary with size, materials and site conditions, so ask for a written estimate after we measure.

Custom Laundry Room Cabinets in Richmond: FAQs

Can you put a countertop over my washer and dryer?

Yes, with front-load machines. We install a counter supported by cleats or side panels, not resting on the machines, with clearance for vibration and to slide the machines out for service. The height is set so you can open the doors and still fold comfortably.

Will wood cabinets hold up in a laundry room?

Plywood cabinets with sealed edges and finishes hold up well. The problem is usually particleboard, which swells quickly when wet. We seal every surface, line sink bases and keep cabinets off wet floors where possible. Hardware and finishes are also chosen to tolerate humidity and occasional splashes.

How high should cabinets be above the machines?

Upper cabinets typically sit 18 to 24 inches above the top of front-load machines or a counter. For top-load washers, we leave enough clearance for the lid to open fully. We check your machine's specifications before setting heights. Taller households sometimes prefer the lower end of that range.

Does Ace Kustoms work in Richmond?

Yes. Richmond is part of our regular service area in Fort Bend County, along with nearby Rosenberg, Sugar Land, Rosenberg–Sugar Land Area, Fulshear. We schedule in-home measurements throughout the week and the estimate is free.

How do I get an estimate in Richmond?

Call (281) 660-3903, text us, or send the form on this page with a few photos and rough measurements. We will set up an in-home visit, measure the space and follow up with a written, itemized estimate.

Planning guides

Storage & Built-Ins · 7 min read